Daftar Standar ISO 200-499 adalah kumpulan judul dari Standar nomor ISO 200 hingga ISO 499 yang diterbitkan oleh badan ISO Internasional.
Mengenai Standar ISO
ISO (International Organization for Standardization) adalah suatu organisasi atau lembaga nirlaba internasional, yang bertujuan untuk membuat dan memperkenalkan standar dan standardisasi internasional untuk berbagai tujuan.
ISO telah mengembangkan lebih dari 23,755 Standar Internasional dan semuanya tercantum di dalam katalog Standar ISO.
Isi dari standar ISO ini dilindungi oleh hak cipta dan sebagian besar harus melakukan proses pembelian untuk dapat mengakses keseluruhan isinya.
Namun ada sekitar 300 standar yang diproduksi oleh ISO dan IEC Joint Technical Committee (JTC1) telah dinyatakan bersifat bebas dan tersedia untuk umum.
Lebih jelas mengenai Standar ISO dan Badan ISO dapat dibaca pada artikel lain dari standarku.com berikut :
Standar Kerjasama
Didalam daftar standar ISO juga terdapat standar lain hasil kerjasama badan standardisasi lain dengan standar ISO seperti :
- IEC (International Electrotechnical Commission)
- IWA (International Workshop Agreement)
IEC adalah organisasi standardisasi internasional yang menyusun dan menerbitkan standar-standar internasional untuk seluruh bidang elektrik, elektronik dan teknologi yang terkait atau bidang teknologi elektro (electrotechnology).
Lebih jelas mengenai IEC dapat dibaca pada artikel lain dari standarku.com berikut :
IWA adalah dokumen ISO yang dihasilkan bukan melalui proses komite teknis ISO secara penuh, namun melalui workshop meeting.
Pelaku pasar dan pemangku kepentingan lainnya dapat berpartisipasi langsung dalam mengembangkan IWA dan tidak harus melalui delegasi nasional.
Ini adalah cara cepat untuk mendapatkan dokumen ISO yang diakui, prosesnya tidak boleh memakan waktu total lebih dari 12 bulan.
Prosesnya dirancang agar fleksibel dan sebagian besar diputuskan oleh organisasi yang mengajukan.
Daftar Standar ISO 200-499
Keseluruhan Daftar Standar ISO adalah dari ISO 1 hingga ISO 99999, namun terlalu panjang untuk ditampilkan semua pada halaman ini.
Untuk itu kami telah membaginya menjadi beberapa postingan, yang dimulai pada postingan sebelumnya berikut :
- Daftar Standar ISO (ISO 1-99)
- Daftar Standar ISO 100-199
Selanjutnya pada postingan kali ini akan menampilkan Standar ISO seri ISO 200 hingga ISO 499.
Daftar Standar ISO 200 – ISO 229
ISO 204:2018 Metallic materials — Uniaxial creep testing in tension — Method of test
ISO 209:2007 Aluminium and aluminium alloys — Chemical composition
ISO/TS 210:2014 Essential oils — General rules for packaging, conditioning and storage
ISO/TS 211:2014 Essential oils — General rules for labelling and marking of containers
ISO 212:2007 Essential oils — Sampling
ISO 214:1976 Documentation — Abstracts for publications and documentation
ISO 215:1986 Documentation — Presentation of contributions to periodicals and other serials
ISO 216:2007 Writing paper and certain classes of printed matter — Trimmed sizes — A and B series, and indication of machine direction
ISO 217:2013 Paper — Untrimmed sizes — Designation and tolerances for primary and supplementary ranges, and indication of machine direction
ISO 225:2010 Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
ISO 226:2003 Acoustics — Normal equal-loudness-level contours
ISO 228 Pipe threads where pressure-tight joints are not made on the threads
ISO 229:1973 Machine tools — Speeds and feeds
Daftar Standar ISO 230 – ISO 239
ISO 230 Test code for machine tools
ISO 230-1:2012 Part 1: Geometric accuracy of machines operating under no-load or quasi-static conditions
ISO 230-2:2014 Part 2: Determination of accuracy and repeatability of positioning of numerically controlled axes
ISO 230-3:2020 Part 3: Determination of thermal effects
ISO 230-4:2005 Part 4: Circular tests for numerically controlled machine tools
ISO 230-5:2000 Part 5: Determination of the noise emission
ISO 230-6:2002 Part 6: Determination of positioning accuracy on body and face diagonals (Diagonal displacement tests)
ISO 230-7:2015 Part 7: Geometric accuracy of axes of rotation
ISO/TR 230-8:2010 Part 8: Vibrations
ISO/TR 230-9:2005 Part 9: Estimation of measurement uncertainty for machine tool tests according to series ISO 230, basic equations
ISO 230-10:2016 Part 10: Determination of the measuring performance of probing systems of numerically controlled machine tools
ISO/TR 230-11:2018 Part 11: Measuring instruments suitable for machine tool geometry tests
ISO/R 231:1961 Paper vocabulary — Third series of terms [Withdrawn: Replaced with ISO 4046]
ISO 233 Information and documentation — Transliteration of Arabic characters into Latin characters[Note 3]
ISO 234 Files and rasps
ISO 234-1:1983 Part 1: Dimensions
ISO 234-2:1982 Part 2: Characteristics of cut
ISO 235:2016 Parallel shank jobber and stub series drills and Morse taper shank drills
ISO 236 Reamers[Note 3]
ISO 236-1:1976 Hand reamers
ISO 236-2:2013 Part 2: Long fluted machine reamers with Morse taper shanks
ISO 237:1975 Rotating tools with parallel shanks — Diameters of shanks and sizes of driving squares
ISO 238:2016 Reduction sleeves and extension sockets for tools with Morse taper shanks
ISO 239:1999 Drill chuck tapers
Daftar Standar ISO 240 – ISO 249
ISO 240:2016 Milling cutters — Interchangeability dimensions for cutter arbors or cutter mandrels
ISO 241:1994 Shanks for turning and planing tools — Shapes and dimensions of the section
ISO 242:2014 Carbide tips for brazing on turning tools
ISO 243:2014 Turning tools with carbide tips — External tools
ISO 244:1979 Aircraft — Sealing wire
ISO 245:1998 Aerospace — Lockwire — Diameters
ISO 246:2007 Rolling bearings — Cylindrical roller bearings, separate thrust collars — Boundary dimensions
ISO 247 Rubber — Determination of ash
ISO 247-1:2018 Part 1: Combustion method
ISO 247-2:2018 Part 2: Thermogravimetric analysis (TGA)
ISO 248 Rubber, raw – Determination of volatile-matter content
ISO 248-1:2011 Part 1: Hot-mill method and oven method
ISO 248-2:2019 Part 2: Thermogravimetric methods using an automatic analyser with an infrared drying unit
ISO 249:2016 Rubber, raw natural — Determination of dirt content
Daftar Standar ISO 250 – ISO 299
ISO 251:2012 Conveyor belts with textile carcass — Widths and lengths
ISO 252:2007 Conveyor belts — Adhesion between constitutive elements — Test methods
ISO 254:2011 Belt drives — Pulleys — Quality, finish and balance
ISO 255:1990 Belt drives — Pulleys for V-belts (system based on datum width) — Geometrical inspection of grooves
ISO 257:2018 Pesticides and other agrochemicals — Principles for the selection of common names
ISO 259 Information and documentation — Transliteration of Hebrew characters into Latin characters[Note 3]
ISO 261:1998 ISO general purpose metric screw threads — General plan
ISO 262:1998 ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
ISO 263:1973 ISO inch screw threads — General plan and selection for screws, bolts and nuts — Diameter range 0,06 to 6 in
ISO 265 Pipes and fittings of plastics materials — Fittings for domestic and industrial waste pipes — Basic dimensions: Metric series
ISO 265-1:1988 Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
ISO 266:1997 Acoustics — Preferred frequencies
ISO 268:1980 Aircraft — Mechanical and electromechanical indicators — General requirements
ISO 269:1985 Correspondence envelopes – Designation and sizes [Withdrawn without replacement]
ISO 272:1982 Fasteners — Hexagon products — Widths across flats
ISO 273:1979 Fasteners — Clearance holes for bolts and screws
ISO 276:2019 Binders for paints and varnishes — Linseed stand oil — Requirements and methods of test
ISO 277:2002 Binders for paints and varnishes — Raw tung oil — Requirements and methods of test
ISO 279:1998 Essential oils — Determination of relative density at 20 degrees C – Reference method
ISO 280:1998 Essential oils — Determination of refractive index
ISO 281:2007 Rolling bearings — Dynamic load ratings and rating life
ISO 282:1992 Conveyor belts — Sampling
ISO 283:2015 Textile conveyor belts — Full thickness tensile strength, elongation at break and elongation at the reference load — Test method
ISO 284:2012 Conveyor belts – Electrical conductivity – Specification and test method
ISO 286 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes
ISO 286-1:2010 Part 1: Basis of tolerances, deviations and fits
ISO 286-2:2010 Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO 287:2017 Paper and board — Determination of moisture content of a lot — Oven-drying method
ISO 289 Rubber, unvulcanized — Determinations using a shearing-disc viscometer
ISO 289-1:2015 Part 1: Determination of Mooney viscosity
ISO 289-2:2020 Part 2: Determination of pre-vulcanization characteristics
ISO 289-3:2015 Part 3: Determination of the Delta Mooney value for non-pigmented, oil-extended emulsion-polymerized SBR
ISO 289-4:2003 Part 4: Determination of the Mooney stress-relaxation rate
ISO 291:2008 Plastics — Standard atmospheres for conditioning and testing
ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294 Plastics — Injection moulding of test specimens of thermoplastic materials
ISO 294-1:2017 Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 294-2:2018 Part 2: Small tensile bars
ISO 294-3:2020 Part 3: Small plates
ISO 294-4:2018 Part 4: Determination of moulding shrinkage
ISO 294-5:2017 Part 5: Preparation of standard specimens for investigating anisotropy
ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
ISO 296:1991 Machine tools — Self-holding tapers for tool shanks
ISO 297:1988 7/24 tapers for tool shanks for manual changing
ISO 298:1973 Machine tools — Lathe centres — Sizes for interchangeability
ISO 299:1987 Machine tool tables — T-slots and corresponding bolts
Daftar Standar ISO 300 – ISO 349
ISO 301:2006 Zinc alloy ingots intended for castings
ISO 302:2015 Pulps — Determination of Kappa number
ISO 304:1985 Surface active agents — Determination of surface tension by drawing up liquid films
ISO 305:2019 Plastics — Determination of thermal stability of poly(vinyl chloride), related chlorine-containing homopolymers and copolymers and their compounds — Discoloration method
ISO 306:2013 Plastics — Thermoplastic materials – Determination of Vicat softening temperature (VST)
ISO 307:2019 Plastics — Polyamides — Determination of viscosity number
ISO 308:1994 Plastics — Phenolic moulding materials — Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state)
ISO 310:1992 Manganese ores and concentrates — Determination of hygroscopic moisture content in analytical samples — Gravimetric method
ISO 312:1986 Manganese ores — Determination of active oxygen content, expressed as manganese dioxide — Titrimetric method
ISO 315:1984 Manganese ores and concentrates — Determination of nickel content — Dimethylglyoxime spectrometric method and flame atomic absorption spectrometric method
ISO 317:1984 Manganese ores and concentrates — Determination of arsenic content — Spectrometric method
ISO 320:1981 Manganese ores — Determination of sulphur content — Barium sulphate gravimetric methods and sulphur dioxide titrimetric method after combustion
ISO 334:2020 Coal and coke — Determination of total sulfur — Eschka method
ISO 337:1981 Road vehicles — 50 semi-trailer fifth wheel coupling pin — Basic and mounting/interchangeability dimensions
ISO 340:2013 Conveyor belts — Laboratory scale flammability characteristics — Requirements and test method
ISO 344:1981 Textile machinery and accessories — Spinning machines — Flyer bobbins
ISO 349:2020 Hard coal — Audibert-Arnu dilatometer test
Daftar Standar ISO 350 – ISO 399
ISO 354:2003 Acoustics — Measurement of sound absorption in a reverberation room
ISO 355:2019 Rolling bearings — Tapered roller bearings — Boundary dimensions and series designations
ISO 356:1996 Essential oils — Preparation of test samples
ISO 359:1983 Cinematography — Projectable image area on 16 mm motion-picture prints — Dimensions and location
ISO 361:1975 Basic ionizing radiation symbol
ISO 362 Measurement of noise emitted by accelerating road vehicles — Engineering method
ISO 362-1:2015 Part 1: M and N categories
ISO 362-2:2009 Part 2: L category
ISO 362-3:2016 Part 3: Indoor testing M and N categories
ISO 363 Textile machinery and accessories — Flat steel healds with closed end loops
ISO 363-1:2006 Part 1: Dimensions of healds manufactured of rolled steel wire
ISO 363-2:2006 Part 2: Dimensions of healds manufactured of hardened strip steel
ISO 364:1983 Textile machinery and accessories — Twin wire healds for weaving machines with heald frames
ISO 365:1982 Textile machinery and accessories — Twin wire healds with inset mail for Jacquard weaving
ISO 366 Textile machinery and accessories — Reeds
ISO 366-2:2009 Part 2: Dimensions and designation of metal reeds with plate baulk
ISO 366-3:2009 Part 3: Dimensions and designation of metal reeds with double-spring baulk
ISO 366-4:2005 Part 4: Dimensions and designation of plastic-bound metal reeds
ISO 366-5:2006 Part 5: Dimensions and designation of profile capsules
ISO 368:2017 Spinning preparatory, spinning and doubling (twisting) machinery — Tubes for ring-spinning, doubling and twisting spindles, taper 1:38 and 1:64
ISO 369:2009 Machine tools — Symbols for indications appearing on machine tools
ISO/R 372:1964 Paper vocabulary — Fourth series of terms [Withdrawn: Replaced with ISO 4046]
ISO 374 Protective gloves against dangerous chemicals and micro-organisms
ISO 374-1:2016 Part 1: Terminology and performance requirements for chemical risks
ISO 374-2:2019 Part 2: Determination of resistance to penetration
ISO 374-4:2019 Part 4: Determination of resistance to degradation by chemicals
ISO 374-5:2016 Part 5: Terminology and performance requirements for micro-organisms risks
ISO 376:2011 Metallic materials — Calibration of force-proving instruments used for the verification of uniaxial testing machines
ISO 377:2017 Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
ISO 383:1976 Laboratory glassware — Interchangeable conical ground joints
ISO 384:2015 Laboratory glass and plastics ware — Principles of design and construction of volumetric instruments
ISO 385:2005 Laboratory glassware — Burettes
ISO 386:1977 Liquid-in-glass laboratory thermometers — Principles of design, construction and use
ISO 387:1977 Hydrometers — Principles of construction and adjustment
ISO 389 Acoustics — Reference zero for the calibration of audiometric equipment
ISO 389-1:2017 Part 1: Reference equivalent threshold sound pressure levels for pure tones and supra-aural earphones
ISO 389-2:1994 Part 2: Reference equivalent threshold sound pressure levels for pure tones and insert earphones
ISO 389-3:2016 Part 3: Reference equivalent threshold vibratory force levels for pure tones and bone vibrators
ISO 389-4:1994 Part 4: Reference levels for narrow-band masking noise
ISO 389-5:2006 Part 5: Reference equivalent threshold sound pressure levels for pure tones in the frequency range 8 kHz to 16 kHz
ISO 389-6:2007 Part 6: Reference threshold of hearing for test signals of short duration
ISO 389-7:2019 Part 7: Reference threshold of hearing under free-field and diffuse-field listening conditions
ISO 389-8:2004 Part 8: Reference equivalent threshold sound pressure levels for pure tones and circumaural earphones
ISO 389-9:2009 Part 9: Preferred test conditions for the determination of reference hearing threshold levels
ISO 390:1993 Products in fibre-reinforced cement — Sampling and inspection
Daftar Standar ISO 400 – ISO 449
ISO 404:2013 Steel and steel products — General technical delivery requirements
ISO 407:2004 Small medical gas cylinders — Pin-index yoke-type valve connections
ISO 413:1974 Aircraft — Heads of lubricating nipples
ISO 418:2001 Photography — Processing chemicals — Specifications for anhydrous sodium sulfite
ISO 420:1994 Photography — Processing chemicals — Specifications for potassium bromide
ISO 422:1994 Photography — Processing chemicals — Specifications for p-methylaminophenol sulfate
ISO 423:1994 Photography — Processing chemicals — Specifications for hydroquinone
ISO 424:1994 Photography — Processing chemicals — Specifications for anhydrous sodium carbonate and sodium carbonate monohydrate
ISO 428:1983 Wrought copper-aluminium alloys — Chemical composition and forms of wrought products [Withdrawn without replacement]
ISO 433:2017 Conveyor belts — Marking
ISO 439:2020 Steel and cast iron — Determination of silicon content — Gravimetric method
ISO 441:1997 Textile machinery and accessories — Drop wires for warp stop motions for weaving machines without automatic drawing-in
ISO 445:2013 Pallets for materials handling — Vocabulary
ISO 446:2004 Micrographics — ISO character and ISO test chart No. 1 — Description and use
ISO 447:1984 Machine tools — Direction of operation of controls
Daftar Standar ISO 450 – ISO 499
ISO 451:1976 Aircraft — Pressure re-oiling connection
ISO 456:1973 Surface active agents — Analysis of soaps — Determination of free caustic alkali
ISO 457:1983 Soaps — Determination of chloride content — Titrimetric method
ISO 458 Plastics — Determination of stiffness in torsion of flexible materials
ISO 458-1:1985 Part 1: General method
ISO 458-2:1985 Part 2: Application to plasticized compounds of homopolymers and copolymers of vinyl chloride
ISO 461 Aircraft — Connectors for ground electrical supplies
ISO 461-1:2003 Part 1: Design, performance and test requirements
ISO 461-2:1985 Part 2: Dimensions
ISO 463:2006 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges
ISO 464:2015 Rolling bearings — Radial bearings with locating snap ring — Dimensions, geometrical product specifications (GPS) and tolerance values
ISO 466:1976 Cinematography — Image produced by 16 mm motion-picture camera aperture — Position and dimensions
ISO 472:2013 Plastics — Vocabulary
ISO 476:1982 Textile machinery and accessories — Pirn winding machines — Vocabulary
ISO 477:1982 Textile machinery and accessories — Cone and cheese winding machines — Vocabulary
ISO 482:1977 Aircraft — Propulsion units and components — Methods of numbering and describing direction of rotation
ISO 483:2005 Plastics — Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at a constant value
ISO 484
ISO 484-1:2015 Part 1: Propellers of diameter greater than 2,50 m
ISO 484-2:2015 Part 2: Propellers of diameter between 0,80 and 2,50 m inclusive
ISO 485:1973 Aircraft water-methanol pressure connections
ISO 486:1988 Cinematography — 16 mm motion-picture film perforated 8 mm Type R — Cutting and perforating dimensions
ISO 487:1998 Steel roller chains, types S and C, attachments and sprockets
ISO 488:2008 Milk — Determination of fat content — Gerber butyrometers
ISO 489:1999 Plastics — Determination of refractive index
ISO 490:1993 Cinematography — Magnetic stripes and magnetic recording head gaps for sound record on 16 mm motion-picture film perforated along one edge (Type 1) — Positions and width dimensions
ISO 491:2002 Cinematography — 35 mm motion-picture film and magnetic film — Cutting and perforating dimensions
ISO 492:2014 Rolling bearings — Radial bearings — Geometrical product specifications (GPS) and tolerance values
ISO 493:1975 Aircraft — Dimensions for single-hole mounting (Class 1 and Class 2) lever-operated manual switches
ISO 494:2017 Cylindrical shank twist drills — Long series
ISO 496:1973 Driving and driven machines — Shaft heights
ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
ISO 498:1992 Natural rubber latex concentrate — Preparation of dry films
Update Daftar
Untuk daftar lengkap dan terbaru dari semua standar ISO setiap saat, bisa dilihat pada katalog ISO di web resmi ISO international berikut :
https://www.iso.org/standards-catalogue/browse-by-ics.html
Demikian artikel dari standarku.com mengenai Daftar Standar ISO 100-199.
Mohon saran dari pembaca untuk kelengkapan isi artikel ini, silahkan saran tersebut dapat disampaikan melalui kolom komentar.
Baca artikel lain :
Sumber referensi :